| |
WELCOME
FiatECUScan 3.3 is out!
If you have an earlier version installed on your computer then you don't need to uninstall or deactivate it.
Simply download the latest version and install it. It will upgrade your current installation and take the license data from it!
ELM 327 INTERFACE WARNING:
Please note that almost all ELM 327 interfaces produced in the last few months have problems accesing the CAN network.
The problem can be easily fixed by simply removing one resistor from the interface.
The procedure is covered in the following topic on the forum: FAULTY ELM 327 INTERFACES DE-MYSTIFIED (READ HERE).
The OBDLink interfaces have a software problem and will be fully supported by next version of FiatECUScan.
FiatECUScan is a diagnostic tool for Fiat, Alfa and Lancia vehicles.
This diagnostics software allows you to perform various diagnostics of the supported modules.
Diagnostics is performed via k-line (VagCom), ELM 327 1.3(or later) or OBDKey 1.40 interface connection to the vehicle's OBD connector (which
is located near steering wheel) or to a manufacturer-specific connector (for older, pre-2000 cars).
You need to have a k-line (VagCom), ELM 327 v1.3 (or later) or OBDKey v1.40 interface cable in order to use this program.
Bluetooth OBDKey and ELM 327 interfaces are supported but not recommended for special functions (like PROXI Alignment, remote control programming, IMA coding, etc.)!
The program is free for personal use with some limitations (see table below). You can download it from the link below.
NO ONE HAS MY AUTHORIZATION TO SELL THE FREE VERSION OF THIS SOFTWARE either as a bundle with cable or standalone.
THERE ARE EBAY SELLERS SELLING FiatECUScan 2.6, 2.5, 2.3. THIS IS FRAUD! DO NOT BUY FROM THEM!
Supported functions
| Function |
FREE |
REGISTERED
49.95 EUR
Purchase |
| K-Line/VagCom interface |
Yes |
Yes |
| ELM 327 v1.3 (or later) interface |
Yes |
Yes |
| OBDKey 1.40 interface |
Yes |
Yes |
| Read ECU identification |
Yes |
Yes |
| Clear fault codes |
Yes, for the FREE modules |
Yes |
| Read diagnostic data |
Yes, for the FREE modules |
Yes |
| Max number of parameters that can be selected simultaneously |
4 |
Unlimited |
| Actuator tests |
Yes, for the FREE modules |
Yes |
| Parameter monitoring while executing an actuator test |
No |
Yes |
| Reset/Programming functions |
No |
Yes |
| CAN modules diagnostic (See Supported Vehicles section for a list of these modules) |
No |
Yes |
| Display data in graph |
Yes, 1 graph |
Yes, up to 4 graphs |
| Max number of parameters on a graph |
4 |
10 |
| Multiple graph files |
No |
Yes |
| Insert tags in recorded data |
No |
Yes |
| Export data to CSV file |
Yes |
Yes |
| Auto-export data to CSV files |
No |
Yes |
| Import CSV data files |
No |
Yes |
| Multilanguage UI |
Yes |
Yes |
Multilanguage data (parameter names, errors, etc.).
Supported languages: English, Deutsch, Italiano, Français, Polski, Český, Magyar, Русский, Español, Nederlands, Türkçe, Chinese, Danish, Croatian, Portuguese(BR) |
No |
Yes |
| Detailed description for Parameters, Errors, etc. in English |
Yes |
Yes |
| Parameter templates (a pre-selected group of parameters that can be selected with a single keypress) |
No |
Yes |
| Test run on any ECU ("simulation" mode) without interface |
Yes |
Yes |
| Auto-saved logs for each diagnostic session |
No |
Yes |
| 20 minutes time limit for a session |
Yes |
No |
Currentntly supported ECUs:
See Supported Vehicles section for a complete list of supported modules on each make/model
Engine Management
- Bosch EDC15
- Bosch EDC15C7
- Bosch EDC16/CF3 Multijet
- Bosch EDC16/CF4 Multijet
- Bosch EDC16/CF5 Multijet
- Marelli 6JF Multijet
- Marelli 6F3 Multijet
- Marelli 8DF/CF5 Multijet
- Bosch MSA 11
- Lucas DPNC TD100
- Lucas EPIC DCU3F
- Bosch Monomotronic MA1.7.3
- Bosch Motronic M3.7.1
- Bosch Motronic M2.10.3
- Bosch Motronic M2.10.4
- Bosch Motronic M1.5.5
- Bosch Motronic ME2.1
- Bosch Motronic ME3.1
- Bosch Motronic ME7.3.1
- Bosch Motronic ME7.3H4
- Bosch Motronic ME7.3H4M
- Bosch Motronic MED7.11
- Bosch Motronic Me7.6.3/CF4
- Bosch Motronic Me7.9.10/CF5
- Bosch Motronic MeD7.6.1/CF4
- Hitachi MPI
- Magneti Marelli IAW 5NF
- Magneti Marelli IAW 4AF/4EF/59F/5AF
- Magneti Marelli IAW 49F
- Magneti Marelli IAW 5SF3/CF4
- Magneti Marelli IAW 5SF8/CF5
- Magneti Marelli IAW 5SF9/CF5
Gearbox Management
- Marelli SELESPEED (old Alfa 156 SELESPEED)
- Marelli SELESPEED CFC208F
- Marelli SELESPEED CFC209F
- Marelli SELESPEED CFC218F
- Marelli SELESPEED CFC228F
- Marelli SELESPEED CFC300
- Marelli SELESPEED CFC328
- AISIN AF40-6
- AISIN YLII 5
- AISIN YLII 5
- ZF 4HP20
ABS
- Bosch ABS 5.7 VDC/ASR/TC
- Bosch ABS 8 VDC/ASR
- Lucas EBC 430 ABS
- Bosch ABS Teves MK20/MK70
- Bosch ABS 5.3 TC/ASR
- TRW Lucas ABS/ESP
Electric Power Steering
- TRW Electric Power Steering
- Delphi Electric Power Steering
- SAGEM Power Steering
Airbags
- ALLIED MY97 Airbags
- BREED MY97 Airbags
- TRW MY97 Airbags
- AUTOLIV MY99 Airbags
- SIEMENS MY99 Airbags
- TRW MY99 Airbags
- TRW MY03 Airbags
- TRW MY05 Airbags
- AUTOLIV MY06 Airbags
- SIEMENS MY06 Airbags
- AUTOLIV MY07 Airbags
- CONTINENTAL Airbags
- TRW Airbags
Body/Dashboard/Misc.
- Service Interval Reset
- CAN Setup / PROXI Alignment Procedure
- Remote control programming
- Delphi/Marelli Body Computer
- Marelli MF Body Computer
- Marelli Body Computer
- Delphi Body Computer
- Siemens Body Computer
- Visteon Instrument Panel
- Marelli Instrument Panel
- Nippon Instrument Panel
- Siemens Instrument Panel
- Siemens VDO Instrument Panel
- Mannesman VDO Instrument Panel
- Valeo parking control
- Bosch parking control
- BITRON Dirver door, Passenger door and Boot
- G.E. PROCOND Dirver door, Passenger door and Boot
- TRW Dirver door and Boot
- Bosch XENON headlights
- Valeo XENON headlights
- Litronic XENON headlights
- Delphi Climate Control
Requirements:
- Any hardware that runs Windows XP, Windows Vista, Windows 7
- Microsoft .NET Framework Version 2.0 SP1. Free, available from www.microsoft.com.
- K-line/VagCom 409, ELM 327 v1.3+ or OBDKey 1.40 interface
- 1.5GHz CPU and better required
For further details please visit our forum.
Download
You can download current version from here:
FiatECUScan 3.3
The file is an installer. It will install the program and all required files on your computer.
You can purchase a license for the registered version
HERE.
What to expect in next releases:
- Support for more Grande Punto, Punto Evo, 500 modules
- Support for more ECUs connected to CAN network
- Support for more engine ECUs
|
|
FESmobile 1.0.1
demo version available!!!
This is a Windows Mobile diagnostics software for Alfa/Fiat/Lancia.
You can download this demo version from here:
FESmobile 1.0.1
The file is a CAB installer. It will install the program and all required files on your Windows Mobile device.
You have to uninstall the previous version first!
|
 |
 |
 |
 |
 |
 |
 |
|